Installation of the piston of the first cylinder in the provision VMT of a step of compression. Chery Amulet (since 2006 of release)
Chery Amulet since 2006
1. Car device
2. Recommendations about operation
3. Malfunctions in a way
4. Maintenance
5. Engine
5.1. Features of a design
5.2. Possible malfunctions of the engine, their reason and ways of elimination
5.3. Compression check in cylinders
5.4. Removal and installation of protection of a case of the engine
5.5. Replacement of support of a suspension bracket of the power unit
5.6. Installation of the piston of the first cylinder in the provision VMT of a step of compression
5.7. Removal, defektovka and flywheel installation
5.8. Replacement of details of consolidation of the engine
5.9. Head of the block of cylinders
5.10. Removal and engine installation
5.11. Engine repair
5.12. Greasing system
5.13. Cooling system
5.14. Power supply system
5.15. Catching system паров fuels
5.16. Cистема of production of the fulfilled gases
6. Transmission
7. Running gear
8. Steering
9. Brake system
10. Electric equipment
11. Body
12. Appendices
13. Electric equipment schemes
 










5-6-ustanovka-porshnya-pervogo-cilindra-v-polozhenie-vmt-takta-szhatiya.html

5.6. Installation of the piston of the first cylinder in the provision VMT of a step of compression

The piston of the 1st cylinder establish in situation VMT (the top dead point) compression step in order that at the work, connected with removal of a belt of a drive of a camshaft, installation of phases of a gazoraspredeleniye was not broken. At violation of phases of a gazoraspredeleniye the engine will normally not work.
Expose VMT on a label on a camshaft pulley (at installation on labels on a pulley of a cranked shaft in this situation there can be a piston either the 1st, or the 4th cylinder). After that be surely convinced of coincidence of labels on a gear pulley of a cranked shaft. If labels do not coincide, means, installation of phases of a gazoraspredeleniye (the piston of the 1st cylinder is not established in VMT) is broken. In this case it is necessary to remove a belt of a drive of a camshaft and to turn a cranked shaft before combination of labels.
Labels of VMT are put on a gear pulley of a camshaft and on a head of the block of cylinders.
Also labels are put on a gear pulley of a cranked shaft and on a cover of the oil pump. These labels are visible only at the removed pulley of a drive of additional units.
1. Remove belts of a drive of the compressor of the conditioner (see. «Replacement of a belt of a drive of the generator and the conditioner compressor») and the pump of the hydraulic booster of a steering (see. «Replacement of a belt of a drive of the pump of the hydraulic booster of a steering»).
2. Fix a cranked shaft from a provorachivaniye. For this purpose establish the gear shifting lever in the provision of the included transfer and ask the assistant to press a brake pedal.
3. Turn out a bolt of fastening of a pulley of a cranked shaft...
4.... also remove a pulley.
5. Remove covers of a belt of a drive of the gas-distributing mechanism (see. «Replacement of a belt of a drive of the gas-distributing mechanism and its tension roller»).
6. Wrap a bolt of fastening of a pulley of a cranked shaft and turn for it a cranked shaft before coincidence of labels on zubaty pulleys.
7. If labels do not coincide, adjust the provision of a belt on pulleys (see. «Replacement of a belt of a drive of the gas-distributing mechanism and its tension roller»).
8. Establish all removed details as it should be, the return to removal.

«previous page
5.5.3. Replacement of the left back support of a suspension bracket of the power unit
following page»
5.7. Removal, defektovka and flywheel installation