11.21. Replacement of a motionless glazing of a body

Glasses of a wind window and window of a door of a back are pasted in body apertures. Them replace with identical receptions therefore work is shown on an example of glass of a wind window.

It be required to you: a screw-driver with a flat edge, a pricker, a knife, a set for an insert of glasses.

So the set for an insert of glasses looks. It consists of a tuba with glue, a tip of a tuba, an activator/cleaner, soil.

Note In instructions on application of sets of different producers there can be insignificant distinctions. In this regard at performance of this operation be guided by the instruction to the set acquired by you.

Good advice For removal of the pasted glass it is convenient to use a steel string.

1. Remove a glass fringing.	2. Remove facings of forward racks (see. «Removal and installation of facings of salon»).

3. Pierce a glutinous seam the pointed tool (for example, a pricker) and stretch in an opening a string (for example, having grasped a string пассатижами).

4. For convenience of work on the ends of a string it is possible to fix screw-drivers which will serve as handles.

5. Saw a string a glutinous seam on all perimeter of glass (for performance of this operation to you the assistant can be demanded).

6. Remove glass from the car.

Prevention Observe precautionary measures at work with glass. The damaged glass can unexpectedly collapse.

7. Cut off an old seam, leaving a thin layer of glue (1,0–2,0 mm).	8. Put the activator...

9.... on the region of glass and a window aperture on all perimeter.	10. Put soil on perimeter of glass and a window aperture.

Prevention Do not put soil for the remains of old glue.

11. Establish on all aperture rubber pro-rates of the identical thickness preventing contact of glass with elements of a body.

12. During 30 mines after soil drawing evenly put glue on a window aperture (thickness of a layer of 0,5 cm) and on glass perimeter.

13. Establish glass assembled with a fringing on the car.

14. Press and fix glass in any available way (for example, by means of a painting adhesive tape). The period of polymerization of glue makes not less than 2-3 h. During this time the car should not be exposed to any external influences. Even sharp closing of a door can lead to increase of pressure of air in salon and, as a result, to a glass separation. Car operation after an insert of glass is desirable for beginning not earlier than in 24 h.

15. Establish facings of forward racks.

16. Establish water taking away guard, a lattice of a box of airinflow and an internal rear-view mirror.

17. Establish levers of a screen wiper of a wind window together with brushes.

18. Glass of a window of a door of a back replace similarly.

If on new glass of a wind window for any reasons there is no arm of fastening of a rear-view mirror, it is possible to paste an arm to glass independently. For this purpose be required:

– glue the Loctite brands;

– arm of fastening of a mirror;

– pencil-steklograf or piece of chalk;

– alcohol for washing;

– pure paper towel;

– fine-grained emery paper No. 320-360.

1. Put the arm basis to an external surface of glass, having combined its bottom edge with the marking line on glass. Designate on glass a contour of the basis of an arm a steklograf or a piece of chalk. Outline a circle round an installation site of an arm of a little bigger diameter, than the arm basis to limit a zone of cleaning of an internal surface of glass.

2. Wash out soap solution an internal surface of glass and wipe dry a paper towel.

3. Wipe an internal surface of glass the paper towel moistened in alcohol.

4. Process an emery paper granularity No. 320-360 the surface noted by a circle from the interior of glass, wipe the paper towel moistened in alcohol, and let's dry out.

5. Put on surfaces of glass and the basis of an arm glue, being guided by the instruction of firm manufacturer of glue.

6. Put an arm to an internal surface of glass according to a marking and strongly press it on 30-60 page.

7. Later 5 mines remove from glass surpluses of glue with the paper towel moistened with alcohol.