Repair of hinges of a drive of gear shifting. Chery Amulet (since 2006 of release)
Chery Amulet since 2006
1. Car device
2. Recommendations about operation
3. Malfunctions in a way
4. Maintenance
5. Engine
6. Transmission
6.1. Coupling
6.2. Transmission
6.2.1. Features of a design
6.2.2. Possible malfunctions of a transmission, their reason and ways of elimination
6.2.3. Replacement of epiploons of a transmission
6.2.4. Removal and transmission installation
6.2.5. Dismantling and assembly of a transmission and defektovka of its details
6.2.6. Repair of a secondary shaft
6.2.7. Repair of primary shaft
6.2.8. Synchronizer repair
6.2.9. Differential repair
6.2.10. Repair of the mechanism of gear shifting
6.2.11. Repair of hinges of a drive of gear shifting
6.2.12. Removal, installation and repair of the coulisse of a control lever by a transmission
6.2.13. Adjustment of a drive of management by a transmission
6.3. Drives of forward wheels
7. Running gear
8. Steering
9. Brake system
10. Electric equipment
11. Body
12. Appendices
13. Electric equipment schemes
 






8c4a8411



6-2-11-remont-sharnirov-privoda-pereklyucheniya-peredach.html

6.2.11. Repair of hinges of a drive of gear shifting

Fig. 6.6. A gear shifting drive (the inlet pipe is for descriptive reasons removed): 1–hinge of draft of the coulisse of a control lever transmission; 2–draft of the coulisse of the lever of gear shifting; 3–arm of the mechanism of a drive of gear shifting; 4–buffer of the lever of gear shifting; 5–gear shifting lever; 6–lever of a choice of transfers; 7–draft of a choice of transfers; 8–draft of gear shifting

At increase in gaps in a gear shifting drive (fig. 6.6) appears vibration of the lever of gear shifting during movement, and also there is indistinct and complicated a gear shifting. In this case it is necessary to repair drive hinges.
It be required to you: keys «on 10», «on 13», a stripper of lock rings (or kruglogubets), a screw-driver with a flat edge.
1. Unfasten a screw-driver a clamp of the hinge of draft of a choice of transfers...
2.... also disconnect the hinge from a spherical support of the intermediate lever of a choice of transfers.
3. Unclench a screw-driver a spring clamp of draft of gear shifting...
4.... take a clamp from an opening of draft and disconnect draft from the gear shifting lever.
5. Mark mutual position of draft of the coulisse of a control lever by a transmission and naves of the lever of a choice of transfers not to break drive adjustment at return assembly.
6. Weaken an inhaling of a nut of a bolt of klemmovy connection of draft and the lever...
7.... also remove the lever of a choice of transfers from draft, at the same time deducing from its lead the buffer of the lever of gear shifting.
8. Turn out a forward bolt...
9.... and two back bolts of fastening of an arm of the mechanism of a drive of gear shifting...
10.... also remove an arm together with the gear shifting lever.
11. For repair of hinges of the lever of a choice of transfers unfasten a screw-driver a clamp of the hinge of draft of a choice of transfers...
12.... also remove the hinge from a spherical finger of the lever.

Note
Draft of a choice of transfers is made assembled with hinges therefore at emergence люфтов in hinges replace draft assembled.

13. Wring out a screw-driver a spring clamp of an antisplash guard...
14.... also remove a guard from the lever.
15. Remove from a spherical finger of the lever a rubber dempfiruyushchy washer.

Note
Strongly pressed out or hardened dempfiruyushchy washer replace.

16. Unscrew a nut of a bolt of klemmovy connection, take a bolt from openings of a coupling collar...
17.... also remove a collar from a lever nave.
18. For repair of hinges of the lever of gear shifting press пассатижами for the direct end of a spring clamp of draft of gear shifting...
19.... take a clamp from a draft opening...
20.... also disconnect draft from the lever.
21. Unscrew a nut of fastening of the lever to an axis...
22.... also remove the lever from an axis.
23. Unclench the ends of a spring clamp of an axis...
24.... remove a clamp...
25.... also take an axis from arm plugs.

Notes
At damage or wear of the buffer of the lever replace its axis assembled with the buffer.
At damage or wear of directing draft of the coulisse of a control lever with a transmission replace an arm assembled with directing, as knot connection not folding.

26. Take from arm openings plastic plugs of an axis of the lever of gear shifting.

Note
Strongly worn-out plugs replace.

27. Collect a drive of management of a transmission and establish it on the car as it should be, the return to dismantling and removal. At connection of the lever of gear shifting with draft of the coulisse of a control lever a transmission combine the labels put before dismantling.

«previous page
6.2.10. Repair of the mechanism of gear shifting
following page»
6.2.12. Removal, installation and repair of the coulisse of a control lever by a transmission