Replacement of a radiator of system of cooling. Chery Amulet (since 2006 of release)
Chery Amulet since 2006
1. Car device
2. Recommendations about operation
3. Malfunctions in a way
4. Maintenance
5. Engine
5.1. Features of a design
5.2. Possible malfunctions of the engine, their reason and ways of elimination
5.3. Compression check in cylinders
5.4. Removal and installation of protection of a case of the engine
5.5. Replacement of support of a suspension bracket of the power unit
5.6. Installation of the piston of the first cylinder in the provision VMT of a step of compression
5.7. Removal, defektovka and flywheel installation
5.8. Replacement of details of consolidation of the engine
5.9. Head of the block of cylinders
5.10. Removal and engine installation
5.11. Engine repair
5.12. Greasing system
5.13. Cooling system
5.13.1. Features of a design
5.13.2. Possible malfunctions of system of cooling, their reason and ways of elimination
5.13.3. Removal and installation of electrofans of a radiator of system of cooling
5.13.4. Replacement of a radiator of system of cooling
5.13.5. Replacement of the water pump
5.13.6. Removal and thermostat installation
5.13.7. Removal and installation of a broad tank
5.14. Power supply system
5.15. Catching system паров fuels
5.16. Cистема of production of the fulfilled gases
6. Transmission
7. Running gear
8. Steering
9. Brake system
10. Electric equipment
11. Body
12. Appendices
13. Electric equipment schemes
 






8c4a8411



5-13-4-zamena-radiatora-sistemy-okhlazhdeniya.html

5.13.4. Replacement of a radiator of system of cooling

The radiator is subject to replacement at detection of a leak of cooling liquid.
The radiator can be checked and repaired in a workshop having the special equipment.

Prevention
Remove a radiator only on the cold engine.

It be required to you: a key «on 10», бокорезы, a screw-driver with a flat edge, пассатижи with changeable capture.
1. Disconnect a wire from the minus plug of the storage battery.
3. Merge cooling liquid (see. «Replacement of cooling liquid»).

Note
For plum it is required to disconnect taking-away hose from a radiator branch pipe as openings for plum of cooling liquid in a radiator are not present.

4. Have a bite a collar of fastening of a parootvodyashchy hose...
5.... also disconnect a hose from the radiator union.
6. Weaken a collar of fastening of a bringing hose to a radiator branch pipe, having compressed пассатижами its unbent ears, shift a collar on a hose...
7.... also disconnect bringing hose from a radiator branch pipe.
8. Turn out bolts of fastening of arms of the top support of a radiator to the top cross-piece of a frame of a radiator.

Note
Together with the right top support of a radiator to a cross-piece the holder of an emphasis of a cowl fastens. Do not forget to put it into place at radiator installation.

9. Incline a radiator towards the engine...
10.... remove arms of the top support of a radiator assembled with pillows...
11.... also take a radiator from a motor compartment.

Notes
The rubber pillows of the bottom support established in openings in a forward stretcher are put on pins in the lower part of each tank of a radiator. Take out them from a stretcher if they remained in its openings, or remove from pins and examine.
Strongly pressed out or hardened pillows replace.
Similarly take out pillows from arms of the top support...
... examine them and if necessary replace.

12. Wash out a radiator outside a stream of water and dry. If on plastic tanks of a radiator there are cracks, replace a radiator.
13. Check tightness of a radiator for what muffle radiator branch pipes, except one to which bring a hose for supply of the compressed air. Lower a radiator in a bath with water and submit air under the pressure of 0,1 MPas (1 kgf/cm2) approximately on 30 villages. The damaged places will leave air bubbles. If the radiator is not located in capacity completely, check it consistently from all directions.
If the leak is found in connection of plastic tanks with a radiator core, it is possible to eliminate it podzhatiy otgibny moustaches of a basic plate of a radiator.
If leak occurs through tube damage, it can be soldered lead solder.
After leak elimination again check tightness of a radiator.
14. Establish a radiator as it should be, the return to removal. At radiator installation adjusting pins from below a radiator should enter into its rubber pillows of fastening.

Good advice
Further to exclude possibility of a podtekaniye of cooling liquid, grease before installation of hoses radiator branch pipes a thin layer of silicone hermetic.

15. Fill in cooling liquid and remove from cooling system air jams (see. «Replacement of cooling liquid»).

«previous page
5.13.3. Removal and installation of electrofans of a radiator of system of cooling
following page»
5.13.5. Replacement of the water pump