Replacement of an epiploon of a camshaft. Chery Amulet (since 2006 of release)
Chery Amulet since 2006
1. Car device
2. Recommendations about operation
3. Malfunctions in a way
4. Maintenance
5. Engine
5.1. Features of a design
5.2. Possible malfunctions of the engine, their reason and ways of elimination
5.3. Compression check in cylinders
5.4. Removal and installation of protection of a case of the engine
5.5. Replacement of support of a suspension bracket of the power unit
5.6. Installation of the piston of the first cylinder in the provision VMT of a step of compression
5.7. Removal, defektovka and flywheel installation
5.8. Replacement of details of consolidation of the engine
5.8.1. Replacement of laying of a cover of a head of the block of cylinders
5.8.2. Replacement of laying of a head of the block of cylinders
5.8.3. Replacement of maslosjemny caps
5.8.4. Replacement of an epiploon of a camshaft
5.8.5. Replacement of epiploons of a cranked shaft
5.8.6. Replacement of consolidation of an oil case
5.8.7. Replacement of laying of an inlet pipe
5.8.8. Replacement of laying of a final collector
5.9. Head of the block of cylinders
5.10. Removal and engine installation
5.11. Engine repair
5.12. Greasing system
5.13. Cooling system
5.14. Power supply system
5.15. Catching system паров fuels
5.16. Cистема of production of the fulfilled gases
6. Transmission
7. Running gear
8. Steering
9. Brake system
10. Electric equipment
11. Body
12. Appendices
13. Electric equipment schemes
 










5-8-4-zamena-salnika-raspredelitelnogo-vala.html

5.8.4. Replacement of an epiploon of a camshaft

At detection of traces of a podtekaniye of oil through a camshaft epiploon at first check, whether the system of ventilation of a case is littered and whether hoses of system of ventilation of a case are pressed, if necessary eliminate malfunctions. If the leak of oil does not stop, replace an epiploon.
It be required to you: all tools necessary for removal of a drive of the gas-distributing mechanism (see. «Replacement of a belt of a drive of the gas-distributing mechanism and its tension roller»), and also a key «on 19», a screw-driver, the special adaptation for keeping of a pulley of a camshaft or пассатижи, a hammer.
1. Disconnect a wire from the minus plug of the storage battery.
2. Establish the piston of the 1st cylinder in the provision VMT of a step of compression (see. «Installation of the piston of the first cylinder in the provision VMT of a step of compression»).
3. Remove a belt of a drive of the gas-distributing mechanism (see. «Replacement of a belt of a drive of the gas-distributing mechanism and its tension roller»).
4. Turn out a bolt of fastening of a gear pulley of a camshaft, holding a pulley from a provorachivaniye, as is shown in a photo, the special adaptation for keeping of a pulley of a camshaft. At its absence it is possible to use пассатижами: to insert handles into openings of a pulley and a big screw-driver to hold from a provorachivaniye.
5. Remove a pulley.
6. Having hooked a screw-driver, take an epiploon from a camshaft nest.
7. Before installation of a new epiploon examine its working edge. It should be equal, without вырывов, dents and rubber flows. The spring of an epiploon should be whole and unextended. Grease a working edge with engine oil.

Good advice
For simplification of a press fitting of an epiploon make on its landing edge a small facet by means of a file or a small nazhdachny circle.

8. Establish an epiploon in a nest, accurately fill a working edge on a camshaft (for example, by means of a wooden stick) and press against the stop by means of a suitable opravka.
9. Establish all removed details and knots as it should be, the return to removal.
10. Adjust a tension of belts of a drive of the generator and the conditioner compressor (see. «Check of a tension of a belt of a drive of the generator and the conditioner compressor»), and also the pump of the hydraulic booster of a steering (see. «Check and adjustment of a tension of a belt of a drive of the pump of the hydraulic booster of a steering»).

«previous page
5.8.3. Replacement of maslosjemny caps
following page»
5.8.5. Replacement of epiploons of a cranked shaft