Replacement of laying of an inlet pipe. Chery Amulet (since 2006 of release)
Chery Amulet since 2006
1. Car device
2. Recommendations about operation
3. Malfunctions in a way
4. Maintenance
5. Engine
5.1. Features of a design
5.2. Possible malfunctions of the engine, their reason and ways of elimination
5.3. Compression check in cylinders
5.4. Removal and installation of protection of a case of the engine
5.5. Replacement of support of a suspension bracket of the power unit
5.6. Installation of the piston of the first cylinder in the provision VMT of a step of compression
5.7. Removal, defektovka and flywheel installation
5.8. Replacement of details of consolidation of the engine
5.8.1. Replacement of laying of a cover of a head of the block of cylinders
5.8.2. Replacement of laying of a head of the block of cylinders
5.8.3. Replacement of maslosjemny caps
5.8.4. Replacement of an epiploon of a camshaft
5.8.5. Replacement of epiploons of a cranked shaft
5.8.6. Replacement of consolidation of an oil case
5.8.7. Replacement of laying of an inlet pipe
5.8.8. Replacement of laying of a final collector
5.9. Head of the block of cylinders
5.10. Removal and engine installation
5.11. Engine repair
5.12. Greasing system
5.13. Cooling system
5.14. Power supply system
5.15. Catching system паров fuels
5.16. Cистема of production of the fulfilled gases
6. Transmission
7. Running gear
8. Steering
9. Brake system
10. Electric equipment
11. Body
12. Appendices
13. Electric equipment schemes
 






8c4a8411



5-8-7-zamena-prokladki-vpusknojj-truby.html

5.8.7. Replacement of laying of an inlet pipe

Between flanges of a head of the block of cylinders and an inlet pipe the sealing laying made of the pressed asbestine leaf, reinforced by steel is established. At violation of tightness of this laying the engine works roughly («троит»). If it is not possible to eliminate malfunction a tightening of fastening of an inlet pipe, replace laying.
For replacement of laying of an inlet pipe to disconnect any hoses (except a hose of system of ventilation of a case of the engine) and wires it is not required. Their flexibility allows to take away an inlet pipe from a head of the block of cylinders on distance, sufficient for laying removal.
It be required to you: a face head «on 13», пассатижи, a screw-driver with a crosswise edge.
1. Disconnect a cable tip from sector of a drive of a butterfly valve, take a cable braid from an arm and take a cable aside (see. «Adjustment and replacement of a cable of a drive of a butterfly valve»).
2. Disconnect a block of a plait of wires from conclusions of the sensor of provision of a butterfly valve...
3.... from conclusions of a regulator of idling...
4.... from conclusions of the sensor of absolute pressure in an inlet pipe...
5.... and from conclusions of nozzles of system of injection of fuel.
6. Disconnect a block of a plait of wires from conclusions of the sensor of phases of the gas-distributing mechanism...
7.... also take plaits of wires aside.
8. Separate the plastic collar connecting a fuel stage and directing masloizmeritelny щупа.
9. Weaken an inhaling of a collar and disconnect airbringing hose from a branch pipe of throttle knot.
10. Remove a fuel stage and, without disconnecting from it a hose in order to avoid system depressurization, take a stage aside (see. «Removal and installations of a fuel stage»).
11. Remove throttle knot (see. «Removal and installation of throttle knot»).
12. Weaken a collar of fastening of a vacuum hose to a receiver, having compressed its unbent ears, shift a collar on a hose...
13.... also disconnect a hose from a receiver.
14. Weaken a collar inhaling...
15.... also disconnect from a receiver branch pipe a hose of ventilation of a case.
16. Turn out two bolts of fastening of a supporting arm to an inlet pipe and one bolt of fastening to the block of cylinders.
17. Turn out two bolts of fastening of the amplifier to a receiver...
18.... one nut of fastening of the amplifier and an inlet pipe to a head of the block of cylinders...
19.... also remove the amplifier.
20. Unscrew nuts of fastening of an inlet pipe to a head of the block of the cylinder.

Note
Places of fastening of an inlet pipe are so located.

21.... also remove an inlet pipe assembled with a receiver.
22. Remove old laying.
23. Remove the remains of old laying from privalochny surfaces of an inlet pipe and a head of the block of the cylinder.
24. Turn out two bolts 1 and three nuts 2...
25.... also separate a receiver and an inlet pipe.
26. Remove old laying from receiver hairpins.
27. Remove the remains of old laying from privalochny surfaces of an inlet pipe and a receiver.
28. Establish new laying and all removed details as it should be, the return to removal.

«previous page
5.8.6. Replacement of consolidation of an oil case
following page»
5.8.8. Replacement of laying of a final collector