Adjustment and replacement of a cable of a drive of a butterfly valve. Chery Amulet (since 2006 of release)
Chery Amulet since 2006
1. Car device
2. Recommendations about operation
3. Malfunctions in a way
4. Maintenance
5. Engine
5.1. Features of a design
5.2. Possible malfunctions of the engine, their reason and ways of elimination
5.3. Compression check in cylinders
5.4. Removal and installation of protection of a case of the engine
5.5. Replacement of support of a suspension bracket of the power unit
5.6. Installation of the piston of the first cylinder in the provision VMT of a step of compression
5.7. Removal, defektovka and flywheel installation
5.8. Replacement of details of consolidation of the engine
5.9. Head of the block of cylinders
5.10. Removal and engine installation
5.11. Engine repair
5.12. Greasing system
5.13. Cooling system
5.14. Power supply system
5.14.1. Features of a design
5.14.2. Check of pressure of fuel in a power supply system
5.14.3. Pressure decrease in a power supply system
5.14.4. Removal and installation of the air filter
5.14.5. Replacement of the module of the fuel pump
5.14.6. Replacement of a regulator of pressure of fuel
5.14.7. Replacement of a fuel tank
5.14.8. Removal and installation of a fuel stage
5.14.9. Removal, installation and check of nozzles
5.14.10. Adjustment and replacement of a cable of a drive of a butterfly valve
5.14.11. Removal and installation of throttle knot
5.14.12. Check and replacement of a regulator of idling
5.14.13. Removal and installation of a pedal of an accelerator
5.15. Catching system паров fuels
5.16. Cистема of production of the fulfilled gases
6. Transmission
7. Running gear
8. Steering
9. Brake system
10. Electric equipment
11. Body
12. Appendices
13. Electric equipment schemes
 






8c4a8411



5-14-10-regulirovka-i-zamena-trosa-privoda-drosselnojj-zaslonki.html

5.14.10. Adjustment and replacement of a cable of a drive of a butterfly valve

If the butterfly valve not completely opens (the engine does not give full capacity) or is closed (idling turns are unstable), at first try to adjust a cable of a drive of a butterfly valve. If adjustment of a drive of a butterfly valve it is impossible to achieve complete opening or closing of a butterfly valve or the drive jams, replace a drive cable.
It be required to you: a key «on 10», пассатижи.
1. For visual control of moving of a butterfly valve weaken a collar of fastening and disconnect airbringing sleeve from a branch pipe of throttle knot (see. «Removal and installation of the air filter»).
2. At completely pressed pedal of an accelerator (it the assistant should make) check the provision of a butterfly valve — it should be completely open, and at the released pedal of an accelerator — is completely closed. Otherwise the drive is necessary for adjusting.
3. Remove from a cable tip a spring bracket...
4.... and tip moving in an arm opening forward achieve, that the butterfly valve was completely closed. At not completely opening zaslonka tip moving achieve back, that the zaslonka completely opened. Fix a cable tip in new situation, having inserted a bracket into its corresponding flute.
5. For replacement of a cable of a drive of a butterfly valve take out its tip from a groove of sector and disconnect a cable from throttle knot.
6. Deduce a tip of a cover of a cable from an opening of an arm of throttle knot.
7. Turn out a bolt of fastening of an arm of a cable of a drive of a butterfly valve to the inlet pipeline.
8. In salon under the dashboard take a cable tip together with the plug from an opening of a pedal of an accelerator.
9. Remove the plug from a cable tip.
10. Extend a cable in podkapotny space through an opening in a front board.
11. Establish a cable as it should be, the return to removal.
12. After installation adjust a cable tension (see subitem 1-4).

«previous page
5.14.9. Removal, installation and check of nozzles
following page»
5.14.11. Removal and installation of throttle knot