Check of hoses and connections of system of cooling. Chery Amulet (since 2006 of release)
Chery Amulet since 2006
1. Car device
2. Recommendations about operation
3. Malfunctions in a way
4. Maintenance
4.1. General provisions
4.2. Daily service (EO)
4.3. Procedural maintenance
4.3.1. Check and adjustment of a tension of a belt of a drive of the pump of the hydraulic booster of a steering
4.3.2. Check of a tension of a belt of a drive of the generator and conditioner compressor
4.3.3. Check and adjustment of a tension of a belt of a drive of the gas-distributing mechanism
4.3.4. Oil replacement in the engine and the oil filter
4.3.5. Cleaning of system of ventilation of a case
4.3.6. Check of hoses and connections of system of cooling
4.3.7. Replacement of cooling liquid
4.3.8. Tightness check топливопроводов
4.3.9. Replacement of the fuel filter
4.3.10. Replacement of a filtering element of the air filter
4.3.11. Check of system of production of the fulfilled gases
4.3.12. Replacement and service of spark plugs
4.3.13. Replacement of a belt of a drive of the pump of the hydraulic booster of a steering
4.3.14. Replacement of a belt of a drive of the generator and conditioner compressor
4.3.15. Replacement of a belt of a drive of the gas-distributing mechanism and its tension roller
4.3.16. Check and adjustment of a drive of switching off of coupling
4.3.17. Check of level and oil replacement in a transmission
4.3.18. Check of protective covers of hinges of equal angular speeds
4.3.19. Check of a technical condition of details of a forward suspension bracket on the car
4.3.20. Check of a technical condition of details of a back suspension bracket on the car
4.3.21. Check and adjustment of corners of installation of wheels
4.3.22. Survey and steering check on the car
4.3.23. Check of a free wheeling (люфта) steering wheel
4.3.24. Check of tightness of a hydraulic actuator of brake system
4.3.25. Check of operation of the vacuum amplifier of brakes
4.3.26. Check of degree of wear of brake shoes, disks and drums
4.3.27. Replacement of brake liquid in a hydraulic actuator of brakes
4.3.28. Check of overall performance of brake system
4.3.29. Check of the parking brake
4.3.30. Service of the storage battery
4.3.31. Check and adjustment of light of headlights
4.3.32. Greasing of fittings of a body
4.3.33. Replacement of the salonny filter of system of heating and conditioning
4.3.34. Pro-cleaning of drainage openings of a body
5. Engine
6. Transmission
7. Running gear
8. Steering
9. Brake system
10. Electric equipment
11. Body
12. Appendices
13. Electric equipment schemes
 






8c4a8411



4-3-6-proverka-shlangov-i-soedinenijj-sistemy-okhlazhdeniya.html

4.3.6. Check of hoses and connections of system of cooling

1. Open a cowl and examine podkapotny space. At survey of the engine pay attention to availability of cooling liquid in a broad tank, on an integrity of rubber hoses, a radiator...
2.... and thermostat cases.

Good advice
The burst hose can be restored temporarily by means of a sticky tape.
Especially well the reinforced sticky tape is suitable for this purpose (for example, silvery color) which can be got in autoshops.

At a podtekaniye of cooling liquid from under the case of the thermostat tighten bolts of its fastening. If with a tightening of bolts to eliminate a podtekaniye it was not possible, it is necessary to uncover and replace laying.
3. Examine connections with a radiator of parootvodyashchy and bringing hoses...
4.... connection of a taking-away hose with a branch pipe of a radiator and a branch pipe of the water pump.
5. Examine connections of hoses of system of cooling with branch pipes of a radiator of a heater...
6.... connection of a bringing hose of a radiator of a heater with the union of a head of the block of cylinders...
7.... connections of a taking-away hose of a radiator of a heater...
8.... and a refueling hose with a pipe of a small circle of circulation of cooling liquid.
9. Check connection of hoses with a broad tank.

Good advice
In a stopper of a broad tank two valves are established: inlet and final. The final valve plays large role in providing an optimum temperature mode of the engine. It supports in system superfluous pressure not less than 0,145 MPas (1,45 kgfs/cm2), providing temperature increase of the beginning of boiling of cooling liquid and preventing intensive steam formation. Unfortunately, when jamming valve in a closed position at an overheat there is a considerable excess of superfluous pressure — more than 0,15 MPas (1,5 kgfs/cm2) that can lead to a rupture of a broad tank or failure of one of hoses. In turn, valve jamming in open situation leads to premature boiling of cooling liquid.
Therefore once a year wash out a stopper of a broad tank flowing water. If there were doubts in serviceability of the valve, replace a stopper.

«previous page
4.3.5. Cleaning of system of ventilation of a case
following page»
4.3.7. Replacement of cooling liquid