Check of degree of wear of brake shoes, disks and drums. Chery Amulet (since 2006 of release)
Chery Amulet since 2006
1. Car device
2. Recommendations about operation
3. Malfunctions in a way
4. Maintenance
4.1. General provisions
4.2. Daily service (EO)
4.3. Procedural maintenance
4.3.1. Check and adjustment of a tension of a belt of a drive of the pump of the hydraulic booster of a steering
4.3.2. Check of a tension of a belt of a drive of the generator and conditioner compressor
4.3.3. Check and adjustment of a tension of a belt of a drive of the gas-distributing mechanism
4.3.4. Oil replacement in the engine and the oil filter
4.3.5. Cleaning of system of ventilation of a case
4.3.6. Check of hoses and connections of system of cooling
4.3.7. Replacement of cooling liquid
4.3.8. Tightness check топливопроводов
4.3.9. Replacement of the fuel filter
4.3.10. Replacement of a filtering element of the air filter
4.3.11. Check of system of production of the fulfilled gases
4.3.12. Replacement and service of spark plugs
4.3.13. Replacement of a belt of a drive of the pump of the hydraulic booster of a steering
4.3.14. Replacement of a belt of a drive of the generator and conditioner compressor
4.3.15. Replacement of a belt of a drive of the gas-distributing mechanism and its tension roller
4.3.16. Check and adjustment of a drive of switching off of coupling
4.3.17. Check of level and oil replacement in a transmission
4.3.18. Check of protective covers of hinges of equal angular speeds
4.3.19. Check of a technical condition of details of a forward suspension bracket on the car
4.3.20. Check of a technical condition of details of a back suspension bracket on the car
4.3.21. Check and adjustment of corners of installation of wheels
4.3.22. Survey and steering check on the car
4.3.23. Check of a free wheeling (люфта) steering wheel
4.3.24. Check of tightness of a hydraulic actuator of brake system
4.3.25. Check of operation of the vacuum amplifier of brakes
4.3.26. Check of degree of wear of brake shoes, disks and drums
4.3.27. Replacement of brake liquid in a hydraulic actuator of brakes
4.3.28. Check of overall performance of brake system
4.3.29. Check of the parking brake
4.3.30. Service of the storage battery
4.3.31. Check and adjustment of light of headlights
4.3.32. Greasing of fittings of a body
4.3.33. Replacement of the salonny filter of system of heating and conditioning
4.3.34. Pro-cleaning of drainage openings of a body
5. Engine
6. Transmission
7. Running gear
8. Steering
9. Brake system
10. Electric equipment
11. Body
12. Appendices
13. Electric equipment schemes
 










4-3-26-proverka-stepeni-iznosa-tormoznykh-kolodok-diskov-i-barabanov.html

4.3.26. Check of degree of wear of brake shoes, disks and drums

It be required to you: calliper or ruler.

Note
If when braking the car withdraws aside or extraneous noise is audible, check a condition of brake shoes.

1. Establish the car on the lift or a jack (supports).
2. Remove a forward wheel.
3. Check through an opening in the case of a brake bracket a condition of blocks. If thickness of frictional overlays of less admissible (tab. 4.3), replace brake shoes (see. «Replacement of brake shoes of the brake mechanism of a forward wheel»).
4. Measure thickness of a brake disk. If its thickness of less admissible (see tab. 4.3), replace a brake disk (see. «Replacement of a brake disk»).

Table of 4.3 Sizes of brake shoes, disks and drums, mm

Note
Minimum admissible thickness of a brake disk is specified on a flange of a brake disk.

5. For check of degree of wear of brake shoes of the back brake mechanism remove a back wheel and a brake drum (see. «Removal and installation of a brake drum»).
6. Measure thickness of a frictional slip together with the basis. If thickness of less admissible (see tab. 4.3), replace blocks (see. «Replacement of brake shoes of the brake mechanism of a back wheel»).

Note
Replace blocks in the following cases:
– thickness of frictional slips less than 2 mm;
– the surface of slips is greasy;
– slips are unsteadily connected to the basis.

7. Measure diameter of a working surface of a brake drum. If it more admissible (see tab. 4.3), replace a drum (see. «Replacement of a brake drum»).

Note
The most admissible working diameter of a brake drum is specified (in inches) on its outer side.

«previous page
4.3.25. Check of operation of the vacuum amplifier of brakes
following page»
4.3.27. Replacement of brake liquid in a hydraulic actuator of brakes